Door Hanger Sizes

Beta
Wally, the 4OVER4 mascot

I hang around doors for a living. Mind the hole, it bites.

Rack cards, menus, door hangers and table tents. Every size below is one the 4OVER4 configurator offers.

Size
3 1/2 in8 1/2 in
Bleed 1/8 inTrimSafe 1/8 in
Format
Door hanger
Trim size
3 1/2 x 8 1/2 in
In millimetres
88.9 x 215.9 mm
Document size with bleed
3 3/4 x 8 3/4 in
Safe area
1/8 in inside the trim
Pixels at 300 DPI
1125 x 2625 px
Printed as
Door Hangers
Die-cut hole
1 1/2 in across, 1 1/2 in from the top

4OVER4 asks for 1/8 in of bleed on standard print and 1/4 in on large format. This page uses the standard figure because the configurator marks this product as standard print.

A door hanger is a rack card with a hole in it. The exact die varies, so keep the top 2 in clear and confirm the die before the run.

Treat the hole as a hard exclusion. Nothing readable within half an inch of it, and nothing at all in the slit that runs from the hole to the top edge.

Every size in these formats

SizeFormatMillimetresProduct
3.5 x 8.5 inDoor hanger88.9 x 215.9 mmDoor Hangers
3.5 x 11 inDoor hanger88.9 x 279.4 mmDoor Hangers
4.25 x 11 inDoor hanger108 x 279.4 mmDoor Hangers
4.25 x 14 inDoor hanger108 x 355.6 mmDoor Hangers

BetaThis is in beta, so some things may not work yet. We’d love your feedback.Send feedback

What the Door Hangers configurator says about size

Sizes
The configurator offers 4 sizes for this product. Every one of them is listed above, exactly as the configurator lists it.
Custom size
This product does not take a custom size. Pick one of the sizes above, or contact us if you have a custom order.

Enjoying this tool?

You might also like Door Hangers

The size you just checked is a door hanger we print, with the hanger hole die-cut where this tool drew it.

Door HangersDoor HangersFrom $290.414.9·64 reviewsShop now

About the door hanger size

A door hanger is a rack card with a hole in it, and the hole is where designs go wrong. Pick a size and see the die drawn to scale, with the area the hole eats.

The standard door hanger is 4.25 x 11 inches. 4OVER4 also prints 4.25 x 14, 3.5 x 8.5 and 3.5 x 11 inches. The hanger hole is about 1.5 inches across, so keep the top two inches clear.

Get the free Door Hangers template

The hole is not decoration

A door hanger hangs from a handle, so a hole is die-cut near the top, usually about 1.5 inches across with its centre about 1.5 inches down. Everything in that circle is gone, and the ring of card around it is structural: put a logo there and it tears off the first windy afternoon.

Keep the top two inches clear of anything that has to be read. The exact die varies by press run, so confirm it with us before a long run.

Which size for which job

4.25 x 11 in is the standard and the one most people mean. 4.25 x 14 in gives you a tear-off coupon at the bottom. 3.5 x 8.5 in and 3.5 x 11 in are the slim versions, cheaper to print and post, and they still fit a standard handle.

All four are read at arm's length on a doorstep, so 300 DPI at the finished size is right and the headline wants to be big.

Common questions

Questions about door hanger sizes

What size is a door hanger?

The standard is 4.25 x 11 inches. 4OVER4 also prints 4.25 x 14, 3.5 x 8.5 and 3.5 x 11 inches.

How big is the hole on a door hanger?

About 1.5 inches across with its centre about 1.5 inches from the top. The exact die varies, so keep the top two inches clear and confirm the die before a long run.

How much bleed does a door hanger need?

0.125 inches on every edge, the same as any small-format piece, and the tool draws it for you.

Can a door hanger have a tear-off coupon?

Yes. The 4.25 x 14 inch size is the one to pick, and we perforate it on press.

FSC CertifiedPrinter #C013635
G7 CertifiedColor Accuracy
25+ YearsSince 1999
150,000+Businesses Served